1-82641375-7 Engine Wire Harness for Hitachi ZX330-3 ZX350-3 6HK1
Looking for part 1-82641375-7? This Engine Wire Harness is made for Hitachi ZW220, ZW220-HCMF, ZW250, ZW250-HCMF, ZX330-3, ZX330-3F excavators and reproduces the original harness design, from wire lengths and branch points to the connector types on each end.
Specifications
- Part Name: Engine Wire Harness
- Part Number: 1-82641375-7, 1826413757
- Condition: Aftermarket new
- Product Weight: 2.5 kg / 5.51 lbs
- Brand: TOPARTS
- Warranty: 12 months
- Feature: Matches original routing and length; durable, heat-resistant insulation
Applicable Models
Hitachi ZW220, ZW220-HCMF, ZW250, ZW250-HCMF, ZX330-3, ZX330-3F, ZX350-3-AMS, ZX350H-3, ZX350H-3F, ZX350K-3, ZX350K-3F, ZX350L-3, ZX350LC-3-HCME, ZX350LC-3F-HCME, ZX350LC-3FAMS, ZX400LCH-3, ZX400W-3, etc
How It Works on Your Machine
Think of this harness as the communication line of the engine. Speed sensors, temperature senders, pressure switches and fuel system components all report back through it, and the controller sends its commands out along the same path.
Every start, every throttle change and every load the excavator takes on is managed through this harness. It routes power and data between the ECM and the engine-mounted components, so a single damaged wire here can show up as a problem anywhere in the engine's behaviour.
Hitachi excavators are popular on the used market, and harness replacement is one of the most effective ways to restore an older Hitachi to dependable everyday use.
How to Tell It Is Time for a New One
You may notice:
- Fault codes for sensors, injectors or the ECM appearing on the monitor
- Problems that come and go when the engine heats up or when the machine vibrates
- Sudden loss of power or the engine entering a derated mode
- Visible heat damage, cracked insulation or chafed wires near the engine block
- Gauges for engine temperature or oil pressure reading erratically
If these symptoms persist after checking fuses, batteries and grounds, the wiring itself is the next thing to suspect.
Common Questions
Do I need special tools to install it?
Standard hand tools are usually enough. Labelling connectors and taking photos before removal makes the job much easier.
Is this a genuine or aftermarket part?
Please see the Condition line in the specifications above. Every part is checked for fit and continuity before shipping.
Is this harness plug-and-play?
Yes. It is built to the original layout with matching connectors, so it installs in place of the original without cutting or splicing.
Tips for a Smooth Installation
- Photograph the routing, clip positions and ground points from several angles.
- Clean and inspect the ECM connector pins; bent pins cause more faults than people expect.
- Keep the new harness clear of the exhaust manifold and turbocharger, and refit all heat shields.
- Clear stored fault codes after installation and run the engine to working temperature to confirm everything reads correctly.
The Cost of Waiting
Electrical problems tend to get worse rather than better. Replacing a deteriorating harness at a planned service interval is far cheaper than dealing with a breakdown in the middle of a job, especially on remote sites.
Made to Last on the Job Site
TOPARTS harnesses are made to the original layout so that every connector reaches its component without strain. Protective conduit and tape guard the wires against abrasion, heat and oil in the engine bay and around the frame.
Ordering Information
- Payment Method: PayPal, Stripe, Credit card, Visa, etc.
- Shipping Method: DHL, FedEx, UPS, TNT, USPS EMS, etc.
- Track Your Order: An email containing the tracking number with a link will be sent to you as soon as it ships.
Note: Please verify your part number and match our product pictures to your original item before ordering. If you have any questions, please feel free to contact us. Thanks.





